Author Topic: the weed, thread  (Read 97725 times)

Julian, Bespoke SEXPERT

  • Member
  • Posts: 28932
  • 11x MVP, 1st Posts, HoF, Certified Weblebrity
Re: the weed, thread
« Reply #315 on: July 01, 2021, 12:45:18 pm »
That sounds like a classic example of patient acting as diagnostician
That's why I only accept diagnoses from Dr. House.
LVMH

Re: the weed, thread
« Reply #316 on: July 01, 2021, 05:09:33 pm »
free marijuana seeds july 1 rosslyn metro station 12noon-2pm. get in line now.
line didn't look too bad
https://twitter.com/FitzFox5DC/status/1410641853196779521?s=20

Outside the Rosslyn Metro station was one of four locations where volunteers with VAMJ gave out seeds. The Arlington seed share lasted from 12-2 p.m. and among the four sites, more than 20,000 seeds were distributed, said organizer Adam Eidinger.
« Last Edit: July 01, 2021, 05:15:19 pm by St. Hubbins-hatch ıll|̲̅̅●̲̅̅|̲̅̅=̲̅̅|̲̅̅●̲̅̅|llıl »
slack

Re: the weed, thread
« Reply #317 on: July 01, 2021, 05:41:44 pm »
Had to wait until after 5PM to exercise my right to consume in Virginia!

I think peter tosh would approve

slack

WALKonBack

  • Guest
Re: the weed, thread
« Reply #318 on: July 02, 2021, 03:15:05 pm »
Weed, is so passé now.


sweetcell

  • Member
  • Posts: 21782
  • I don't belong here.
Re: the weed, thread
« Reply #319 on: July 06, 2021, 12:23:26 pm »
What if stress and anxiety get to a person so much that they can't sleep at 4am. Would a weed break help?

a few times i've needed assistance getting back to sleep because of stress that either kept me up or woke me and didn't allow me to get back to sleep.  however, this has been a rare occurrence that i could count on one hand.  if someone is regularly unable to sleep due to stress, i would hope they'd look into solving the underlying issue(s) or consulting a medical professional...  lighting up at 4 am on the reg would be worrisome for me.
<sig>

grateful

  • Member
  • Posts: 10292
  • 👤 👩 👦 📷 📺
    • Wait, the entire rest of the internet exists and you CHOOSE to post here? Who hurt you?
Re: the weed, thread
« Reply #320 on: July 06, 2021, 12:40:03 pm »
They have melatonin for that.

grateful

  • Member
  • Posts: 10292
  • 👤 👩 👦 📷 📺
    • Wait, the entire rest of the internet exists and you CHOOSE to post here? Who hurt you?
Re: the weed, thread
« Reply #321 on: July 15, 2021, 02:25:56 pm »

WALKonBack

  • Guest

WALKonBack

  • Guest
Re: the weed, thread
« Reply #323 on: July 29, 2021, 01:14:14 pm »


Space Freely

  • Member
  • Posts: 10389
Re: the weed, thread
« Reply #325 on: October 06, 2021, 12:50:41 pm »
I don't smoke weed, so I don't know what's normal. Is it normal to smoke weed on your lunch break on telework days?

sweetcell

  • Member
  • Posts: 21782
  • I don't belong here.
Re: the weed, thread
« Reply #326 on: October 06, 2021, 01:12:35 pm »
I don't smoke weed, so I don't know what's normal. Is it normal to smoke weed on your lunch break on telework days?

overall it certainly isn't typical.  i think it depends on 1) one's ability to work while high, 2) how high one gets, and 3) what sort of works needs to be done.  creative or repetitive tasks are candidates for working while stoned; deep analytical work not so much - but that's just me (see point #1).  i'm sure at some point i've consumed during working hours, but i honestly can't remember the last time i did.

some people like to hit the gym while MJ'ed, personally i would lose interest in the weights and end up staring at the TV instead.  YMMV.
<sig>

Re: the weed, thread
« Reply #327 on: October 06, 2021, 01:14:39 pm »
I don't smoke weed, so I don't know what's normal. Is it normal to smoke weed on your lunch break on telework days?
nope
but I do have a good friend who does editing work and is high from the time he gets up and goes to bed
It's all telework and the employer is very happy with his work (been with them for over a decade)
slack

Yada

  • Member
  • Posts: 11900

Re: the weed, thread
« Reply #329 on: November 17, 2021, 10:35:43 am »
^not impressed at all
Why anyone wouldn't just get the pre-made cones to roll joints is beyond me...

Also, didn't realize I was doing it wrong the whole time, I always added the 'filter' when rolling the joint...seems so much easier to add it at the end
slack